Results 1 to 8 of 8

Thread: Overheating help

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Jan 2006
    Posts
    4,215
    Rep Power
    23

    Overheating help

    i have twin 6.2 mpi mercs. I had not used it for about a year, there was a sensor issue and life got in the way. I just serviced the boat to get going again... oil, drive oil, raw water pumps, etc. one engine runs fine, the other overheats within a few minutes of the dock. I assumed thermostat and changed it.... same behavior. It doesn't overheat without load.

    blockage? Something else? I need some ideas to check. Anyone have a "how to" on backflushing the engine?

  2. #2
    Join Date
    May 2003
    Posts
    2,310
    Rep Power
    24
    Overheating issues can be a serious nuisance .
    A little bit more background ?
    It wasn't doing it before you laid it up ?
    Salt or fresh water use ? FWC ?
    Running the cast iron exhaust ?
    I assume Bravo , not Alpha ?
    How old is the package ?
    Just because something's old doesn't mean you throw it away !

  3. #3
    Join Date
    Jan 2006
    Posts
    4,215
    Rep Power
    23
    It wasn't doing it before, I had a sensor issue but otherwise it ran fine.

    Boat is a 2008. Factory exhaust. Salt water, flushed with saltaway, bravo. Has silent choice.

    I'm leaning towards the manifolds being blocked. I'm just baffled as to why the other engine is running fine when it is in the same environment

  4. #4
    Join Date
    May 2003
    Posts
    2,310
    Rep Power
    24
    I have a friend who had a 28zxo . I think it was a 2003 or so . It was kept high and dry on a lift . After a few years he developed an overheating problem , first on one engine . It drove the mechanics totally mad. At low , off plane , speeds it was fine though.
    They went through everything on both engines about 20 times . Water pumps fine , even the stock manifolds and risers were spotless.

    In the end , at which point his bank account was almost empty , some whiz came along and said , 'have you checked the plastic grommets in the transom plate that connect the exterior water hose to the interior hose ? Salt water boat , dry stored , it's about time'

    Be damned if that wasn't it !

    In time the salt (even fresh water sometimes) gets inbetween the hole in the trans plate and grommet and the corrosion crushes the grommet down creating an air leak in the system . At idle / low speeds the connection is below the water but as soon as you get on plane the problem shows itself.
    For some strange reason it also seems to be more common on dry stored Bravo boats than ones left in the water .

    Of course, this might not be your problem at all but it's useful to know !
    Just because something's old doesn't mean you throw it away !

  5. #5
    Join Date
    Nov 2003
    Posts
    12,683
    Rep Power
    34
    A friend had a similar problem. After disassembling the engine, he found the
    aluminum intake manifold/iron head water passages were completely corroded
    closed. Salt water and dissimilar metals can do these things crazy fast.
    George Carter
    Central Florida
    gcarter763@aol.com
    http://kineticocentralfl.com/


    “If you have to argue your science by using fraud, your science is not valid"
    Professor Ian Plimer, Adilaide and Melbourne Universities

  6. #6
    Join Date
    May 2003
    Posts
    2,310
    Rep Power
    24
    Quote Originally Posted by gcarter View Post
    A friend had a similar problem. After disassembling the engine, he found the
    aluminum intake manifold/iron head water passages were completely corroded
    closed. Salt water and dissimilar metals can do these things crazy fast.

    And what's really shocking George, is that nearly all of the new marine engines are made with all sorts of dissimilar metals and no-one tells you.
    I never knew that our 502 had dissimilar metals in it but thankfully got FWC from the factory. The dealer I got the Volvo from said at the time of ordering that he orders FWC on all his engines . Much later I find out that it too has amongst other things an aluminum intake manifold .

    From here on it's FWC on everything for me !
    Just because something's old doesn't mean you throw it away !

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •