Results 1 to 9 of 9

Thread: A little more '67 Ski-Sporter video

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Mar 2005
    Posts
    3,291
    Rep Power
    23

    A little more '67 Ski-Sporter video

    Shot using the GoPro HD with the "open" back on the housing. Someone was sitting in the middle of the back seat, and I think this helped minimize the wind noise, so you can hear the engine.

    The engine is running great, with the exception of the "hole" when you open the secondaries. Right up to 5,000 rpms.

    http://www.youtube.com/watch?v=FHwy4sg5Hco
    “Oh right, because you walked into strippers discount warehouse and said ‘Help me showcase my intellect.’” - Archer

    Bill
    Grand Rapids, Michigan
    1985 Donzi Criterion SS
    1967 Donzi 16 Ski Sporter, C16-409, Has a new home!
    38' Carver Aft Cabin
    1968 Sea Ray SRV 180 w/1975 70 hp Evinrude
    10" RIB w/15 hp 1984 Evinrude

  2. #2
    Join Date
    Jul 2004
    Posts
    862
    Rep Power
    20
    Very nice!!!!
    1978 X-18, SBC, Volvo 280T
    Big Grizzly 21 Solas Prop
    Heart Bay, Lake George, NY

  3. #3
    Join Date
    Jul 2002
    Posts
    694
    Rep Power
    22
    Runs and sounds good, except for hesitation when cracking the secondaries. Post on tech. Someone has a remedy.

  4. #4
    Join Date
    Nov 2005
    Posts
    1,459
    Rep Power
    20
    Great video Bill. These will help get you through the winter!

    My boat has the same carb issue at around 1500 RPMs. Just a second or so of hesitation. I've been told that my Holley carb has a vacuum secondary and if I were to change to a carb w/ a mechanical secondary it would improve performance.

    My Ski Sporter doesn't really pull skiers anymore and I generally ease the boat out of the hole, but I'm considering a different carb.

    B.O.A.T. = Break Out Another Thousand (actually about $800).

    Motor heads - please chime in........

  5. #5
    Join Date
    Mar 2005
    Posts
    3,291
    Rep Power
    23
    Jay,

    The issue with mine is the secondaries opening, which happens around 4,200 rpms. I believe the spring that controls vacuum secondaries on my carb is too strong. 715 cfm is a lot of carb for a 350 ci engine, and I don't believe it creates enough vacuum for the spring. A smaller carb = more vacuum (like sucking the same volume of air through a shop vac hose, or a garden hose. There is going to be a lot more vacuum through the smaller hose). I can adjust by putting in a weaker spring. 4,200 always seemed high for them to be opening anyway.

    Thanks for the kind words.
    “Oh right, because you walked into strippers discount warehouse and said ‘Help me showcase my intellect.’” - Archer

    Bill
    Grand Rapids, Michigan
    1985 Donzi Criterion SS
    1967 Donzi 16 Ski Sporter, C16-409, Has a new home!
    38' Carver Aft Cabin
    1968 Sea Ray SRV 180 w/1975 70 hp Evinrude
    10" RIB w/15 hp 1984 Evinrude

  6. #6
    Join Date
    Jul 2003
    Posts
    466
    Rep Power
    0
    I prefer mechanical secondaries for that instant hit.

    Moving to a smaller carb, isn't going to change the amount of air that you're motor is pumping.

    Ten years ago, when dirt bikes were changing from two strokes to four strokes, the "bog" at the bottom end was a problem with nearly every big "one lung." The fix was to throw an edelbrock qwiksilver pumper carb on.

    My carb on the boat has mechanical secondaries and "double pumpers" and it's very responsive at all RPM.

    There are a couple guys that do great job on custom marine carbs, send them your specs and they'll send you a carb that will 99% chance be spot on.
    DUNESMAN

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •