Search:

Type: Posts; User: silverghost; Keyword(s):

Search: Search took 0.45 seconds.

  1. Replies
    683
    Views
    68,885

    Greg~ Any Surface Tension project progress...

    Greg~

    Any Surface Tension project progress updates ?
  2. Replies
    683
    Views
    68,885

    Greg~ Pretty slick storage bin. This storage...

    Greg~
    Pretty slick storage bin.
    This storage solution must have pushed this project's retail build cost up to near the $300,000 .
    If you were to actually mass market this boat~~~that is .
    ...
  3. Replies
    683
    Views
    68,885

    Greg~ Any update on the Windscreens & their...

    Greg~

    Any update on the Windscreens & their fabrication for your bench Eggbeater project here ?
  4. Replies
    683
    Views
    68,885

    Greg~ I have been involved in Antique & Classic...

    Greg~
    I have been involved in Antique & Classic Car restorations most of my life.
    Since the musclecar & hotrod/streetrod craze took-off the plating prices have gone through the roof.
    The platers...
  5. Replies
    683
    Views
    68,885

    Chrome Plating $

    Greg~
    Chrome plating prices today have gone through the roof.
    BUT~
    That quote of $ 225. per/hinge set seems off the charts.

    I would go with Cast Stainless Steel, if at all possible, because of...
  6. Replies
    683
    Views
    68,885

    Finish It Already !

    Greg~
    When do you think your great benchseat eggbeater project will be "Officially" finished ?
    What is your timetable ?
    Will it be completed before Labor Day ?

    My Mother used to call all of...
  7. Replies
    683
    Views
    68,885

    Greg: What is the typical required re-build...

    Greg:
    What is the typical required re-build time on a non high-performance outboard in hours ?
    I assume the newer four strokes are better than the older two strokes.

    In it's early...
  8. Replies
    683
    Views
    68,885

    You had wondred why I have never been a big...

    You had wondred why I have never been a big outboard fan~~~
    When I look at the 200 & 600 hour rebuild times you mention above it just scares me away from using any high-peformance outboard.
    Heck...
  9. Replies
    683
    Views
    68,885

    High Life: Thank's for the offer ~~~ But...

    High Life:
    Thank's for the offer ~~~
    But I've never been much of an outboard guy.
    I like Inboards , I/O, and jet-drives.
    --- Still working on my drive-less Benchseat 18 project~~~
    ---And...
  10. Replies
    683
    Views
    68,885

    Greg: There seems to be a sudden flood of...

    Greg:

    There seems to be a sudden flood of Donzi Baby 16 outboards on the market today~~~

    Do you see a possible Donzi Baby 16 Benchseat II project in your future ?
  11. Replies
    683
    Views
    68,885

    Greg: With all the great design & engineering,...

    Greg:
    With all the great design & engineering, + cash & build hours, you three guys put into this fantastic benchseat project I hope you saved some spare cash for a great high horsepower egg-beater...
  12. Replies
    683
    Views
    68,885

    Stay away from that Perko & Attwood Diecast Zamak...

    Stay away from that Perko & Attwood Diecast Zamak Zink junk !
    This hardware stuff self-destructs & pitts while you are looking at it ; especially in a Salt water & air environment !

    I...
  13. Replies
    683
    Views
    68,885

    Greg: In your post #380 above I have the second...

    Greg:
    In your post #380 above I have the second Take-apart hinge pair, from the top of your photos, on my motorbox of my American Skier Eagle.

    Mine are Chrome on Brass but I see the very same...
Results 1 to 13 of 13