Search:

Type: Posts; User: bigdawgchallenger; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    375

    That may work. this is molded plastic that...

    That may work.

    this is molded plastic that covers a 90 deg corner. It appears to be in four pieces. Top, Bottom, left, and right.

    I will add a picture when im able.
  2. Replies
    3
    Views
    375

    1999 38 ZX cabin door trim

    Anyone know where to get a replacement or an alternative that will look good?

    its the white (yellow now) molded plastic
  3. Replies
    0
    Views
    168

    1999 38 ZX Daytona

    Does anyone know the fuel tank capacity?
  4. Replies
    3
    Views
    466

    bttt Ok, $300

    bttt

    Ok, $300
  5. Replies
    16
    Views
    974

    yes, its built into the oil pan

    yes, its built into the oil pan
  6. Replies
    16
    Views
    974

    Oil change time, only putting in 10 plus filling...

    Oil change time, only putting in 10 plus filling filter.
  7. Replies
    16
    Views
    974

    there is baffles 45 to 50 psi warm.

    there is baffles
    45 to 50 psi warm.
  8. Replies
    16
    Views
    974

    That was one of my thoughts, I have a Milodon 10...

    That was one of my thoughts, I have a Milodon 10 Qt pan with a Milodon dip stick, however it takes 12 Qts to bring it up to the full mark, 13 with the filter. I think something may be off with the...
  9. Replies
    16
    Views
    974

    Glad all is well. No synthetic oil was used.

    Glad all is well.

    No synthetic oil was used.
  10. Replies
    16
    Views
    974

    Hey Bill, how are you? Both engines were...

    Hey Bill, how are you?
    Both engines were recently rebuilt, one has 60 hours on it and the other has 20 hours on it, shouldn't the rings completely seated by now?
  11. Replies
    16
    Views
    974

    What would cause

    What would cause an excessive amount of oil to come out of the valve cover vents into the carb? gen IV 454

    Mike
  12. Replies
    3
    Views
    466

    electric

    electric
  13. Replies
    3
    Views
    466

    Two Edelbrock 750 CFM Carbs

    Edelbrock 1410 carbs
    60 Hours on them. Made some changes and had to step up carb size. $375 for both or $200 each, plus shipping

    http://www.summitracing.com/parts/EDL-1410/

    Mike 216-315-0125
  14. Replies
    9
    Views
    555

    use a couple of 3" extensions, you can do it but...

    use a couple of 3" extensions, you can do it but it is a pita
  15. Replies
    4
    Views
    531

    I tried to get it out today, damn weather didn't...

    I tried to get it out today, damn weather didn't cooperate though. I will do the temp gun thing tomorrow I hope.

    Mike
  16. Replies
    4
    Views
    531

    Help, High oil temp problems

    Is there a pressure relief valve in the oil filter relocation adapter on my gen IV 454? My oil temp will not come down. I am thinking if there is a valve, maybe it has failed and is letting the oil...
  17. Replies
    9
    Views
    493

    I just put on new oil coolers on both engines. ...

    I just put on new oil coolers on both engines. They were used, but clean. they are approximately 20" long and 2" in diameter. What else could cause high oil temp? I am baffled. I'm using a 12 Qt...
  18. Replies
    9
    Views
    493

    I'm seeing temps in the 250 range, whats normal/...

    I'm seeing temps in the 250 range, whats normal/ too hot?
  19. Replies
    9
    Views
    493

    Does any one know

    how the oil temperature is taken on a gen IV 454, is it taken as it leaves the engine (hottest) or when it returns to the engine (coolest)?
  20. Replies
    8
    Views
    1,487

    60 with 330hp 62.5 with the 420hp I used some...

    60 with 330hp
    62.5 with the 420hp
    I used some bucherd up 25" props and 22" Hydromotive props. I now have some 23" Hydromotives and will let you know what I get in a few weeks.

    I think it's...
  21. try this guy...

    try this guy http://www.donzi.net/forums/showthread.php?t=62692&highlight=windshield

    I think i have some diagrams, anything specific your looking for (ie engines, interior, etc)?

    Mike
  22. Replies
    9
    Views
    837

    it depends on the type, if they are the small...

    it depends on the type, if they are the small ones, look on the port side of the port engine, down low. if they are the large ones, they should be behind the distributor, extends from head to head...
  23. Replies
    13
    Views
    1,222

    Are you not burning enough gas with the Z33?

    Are you not burning enough gas with the Z33?
  24. Replies
    8
    Views
    1,487

    It's Heavy, not Fast. I went from 330 HP to...

    It's Heavy, not Fast. I went from 330 HP to 420HP and gained 2.5 MPH. all with the Bravo 1

    Mike
  25. Replies
    9
    Views
    837

    Mark, How big are the oil coolers? Remember I...

    Mark, How big are the oil coolers? Remember I had to replace mine? This was the first year of this engine/outdrive for the boat and the oil coolers and drive/engine couplers are undersized. Last...
Results 1 to 25 of 131
Page 1 of 6 1 2 3 4