You could fly cut the adapter plate . It only needs to be as thick as the diameter of the bolt your using for a tapped hole and counter sink for a flat head screws to mount the adaptor to the...
Type: Posts; User: joseph m. hahnl; Keyword(s):
You could fly cut the adapter plate . It only needs to be as thick as the diameter of the bolt your using for a tapped hole and counter sink for a flat head screws to mount the adaptor to the...
http://donzimarine.com/Archives/Brochures/DONZI%20BOATS%201995%20BROCHURE.pdf
There's a little info on it in the brochure
It appears the 210 was a cuddy cabin .
Yes the manifold will bolt on. If you go with a GM Performance block which is used by Mercruiser and it's a one piece main seal hydraulic roller block . the fly wheel will bolt on. The rotating...
I built a 377 for my cruiser with a clearance GM Performance block from Summit and a rotating assembly from Scat. just waiting on spring to put the flywheel and the exhaust manifolds on then it's...
they specialize in below waterline paint
http://www.bottompaintstore.com/topside-boat-paint-above-or-below-the-waterline-c-13630_13804.html
Dump the aluminum prop. They don't work well with V8s . A 21 Mirage which is stainless should put you between 4600 and 5000 RPM The 69 barrel back has the lifting strake running all the way to the...
I bought a PDF file off E-bay for my Alpha. Short money and it's genuine Merc procedure . It listed all the tools with their part numbers . I was able to just down load, so it was an instant ...
Yes only iron ones for the 302/351. http://www.hgemarine.com/products/manifolds/ford-replacement-hge-1-81.html
http://www.hgemarine.com/products/manifolds/mercruiser-replacement-hge-7114a.html
http://www.hgemarine.com/products/manifolds/mercruiser-replacement-hge-9746a.html
...
There's a 20 on this group for $16K looks very nice:yes:
https://www.facebook.com/groups/222949037794347/?fref=nf
This one seems dialed in pretty good. Carries the bow well. I wonder if this one has the pad that Matty mentioned
https://www.youtube.com/watch?v=UEbO6tra5to
Nice:kingme: glad to hear it's working for you:propeller:
I have found my rear seat gets completely soaked . I have to take it out and let it drain out periodically . The main difference between the front seat bases is they have plywood netting which keeps...
Ice cold does crack vinyl. And sled seats need replacing often . I think the problem lies with the drain holes in the seat deck being to small and the seat gets wet.:lightning
https://www.facebook.com/photo.php?fbid=164045557355768&set=pcb.1198513493526697&type=3&theater
Thanks for the birthday greeting
https://www.instagram.com/p/BHnq5hsDduv/?taken-by=connerhahnl
Check the trailing edge of the lower unit hub . Any raised bur on the hub will cavitate the prop. Check the prop thrust washer and make sure the taper is not worn and rubbing the prop on the lower's...
They are VDO Vangaurd series. It depends on the drive if it has an external or Integrated pitot.
If the gage is bad it can be repaired for the same cost of a new one:shocking:. But seeing as you would need to replace the others gages to match the new speedo The cost is well worth it:yes:
...
I'd like to be around 4800. It seems that the 1.32 is 250 Rpm per inch of pitch. I think ideally a 22P would put me where I want.
Craig thanks for the offer. But I'd like to bump up the...
I tried the 1.32 : 1 Alpha today. I'm glad I waited to do a base line before I pulled the trigger on a new prop. I lost a 1000 rpm around 4000 @ WOT with the 25p. I put the 21 back on and it went...
The narcissist speaks. :worthy:
http://th03.deviantart.net/fs71/200H/f/2012/320/c/c/party_pooper_by_gafagear-d5l77hk.png
I'm in the process of restoring the gloss to my transom. The 3m compound is amazing followed by there glaze. I am going to clear coat for UV protection. when I looked for paint Awlgrip and Imron were...
Sorry but you guy's got it all wrong it should sound like this
https://www.youtube.com/watch?v=pB_xViJUs0E