Search:

Type: Posts; User: katanna; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Restoration

    Looks great! Nothing beats the lines of a classic Chris.
    One complaint, I dont approve of the Magnum being used as scaffolding and a work bench :p
  2. Thread: riser issue

    by katanna
    Replies
    10
    Views
    1,405

    Had a somewhat similar issue with a customers...

    Had a somewhat similar issue with a customers boat. After running it would shut off. If it sat for a while it would restart and could be fine for along time and then it would shut off again. Ended up...
  3. Replies
    4
    Views
    278

    I will try the revolution this weekend. Not...

    I will try the revolution this weekend.
    Not sure what hub is in the hydro, I will pull it tomorrow and check.
  4. Replies
    4
    Views
    278

    Another prop debate

    I ran the minx for the first time with the new full hydraulic steering, bigger tabs, and four blade hydromotive. Steering was incredible, will never have another boat without it. Not loving the...
  5. Replies
    5
    Views
    836

    No picture :smash:

    No picture :smash:
  6. Replies
    5
    Views
    3,849

    You dont see too many without any snaps drilled...

    You dont see too many without any snaps drilled in them. Must use a full cover.
  7. Replies
    9
    Views
    389

    When you got your arm in there, were you going...

    When you got your arm in there, were you going through the locker in the floor, or from the engine compartment?
  8. Replies
    9
    Views
    389

    Seat mounting Minx

    Looking to replace the slides on my Minx seats. There is three phillips head screws holding the aluminum plate to the molded in cockpit pod or riser. Are these screws through bolted with nuts or is...
  9. Replies
    65
    Views
    3,075

    Trim wires?

    Trim wires?
  10. Replies
    65
    Views
    3,075

    Running it on the muffs is not the same as...

    Running it on the muffs is not the same as running it under load. You will build more pressure when running hard. My Magnum Maltese would run all day under muffs, but would blow the circulating hose...
  11. Replies
    630
    Views
    67,021

    I would lean towards the 24 mirage props. My 27...

    I would lean towards the 24 mirage props. My 27 sport and maltese both had the merc 280 motors and the 23 mirage was perfect. I looks like you will have more horsepower than I did.

    Steve
  12. Replies
    65
    Views
    3,075

    Bellows for the shift cable can leak and not show...

    Bellows for the shift cable can leak and not show when sitting. If it bothers you that much drill a hole to let the water out. :hyper:
  13. Replies
    62
    Views
    3,255

    The balance would be alot better with the small...

    The balance would be alot better with the small block. You wont like the way it porposes at cruising speed with the big block.
  14. Replies
    19
    Views
    1,181

    You may need to add a little more vang. :)

    You may need to add a little more vang. :)
  15. Replies
    91
    Views
    17,254

    If you started it for 15 seconds in cold storage...

    If you started it for 15 seconds in cold storage with no hose hooked up, you will need an impeller kit before the sea trial. I wont even roll mine over with no muffs hooked up. The pumps gets wiped...
  16. Replies
    310
    Views
    33,592

    When you get the drive down, leave it that way...

    When you get the drive down, leave it that way till spring. The drive should stored down to increase the life of the boots. They rot faster when stretched in the up position.
  17. Replies
    5
    Views
    379

    What color is it? I had to :hyper:

    What color is it? I had to :hyper:
  18. Replies
    310
    Views
    33,592

    Ultimate would be the best all around trade off....

    Ultimate would be the best all around trade off. It allows for increased speed with less drag and the ability to use more of a surface piercing prop and still be able to get on plane without too much...
  19. Replies
    310
    Views
    33,592

    You want your drive to be down but not all the...

    You want your drive to be down but not all the way. Most drives when all the way down, will have a negative propshaft angle which helps you get on plane. Raise your drive up a little so the prop...
  20. Replies
    6
    Views
    362

    I was afraid the underseat may not be the...

    I was afraid the underseat may not be the greatest. I think I will try and locate some spray paint to match the honey color and shoot the grills so they dont stand out. They are the 131 models which...
  21. Replies
    32
    Views
    1,342

    Running 68 in my Minx with a new 377-325hp crate...

    Running 68 in my Minx with a new 377-325hp crate motor. I have added full hyd steering this winter along with larger tabs and a hydromotive 23p four blade in place of my 3 blade spinelli. If it...
  22. Replies
    6
    Views
    362

    Speaker locations

    Getting ready to install my stereo system. 4- bose flush mount speakers, 2-300 watt amps, head unit, wired remote. I will be installing the head unit behind the dash and control from the full...
  23. Replies
    5
    Views
    545

    1988 Specs length 22'8" Beam 7'0 "

    1988 Specs

    length 22'8"
    Beam 7'0 "
  24. Replies
    17
    Views
    1,257

    Had an envoy. Replied to thread yesterday....

    Had an envoy. Replied to thread yesterday. Moderator hasn't posted yet.
    frustrating
  25. Replies
    32
    Views
    1,342

    What type of water are you looking to use it in?...

    What type of water are you looking to use it in? My python jet with a 460 ford runs in the 90s. Throw in a little chop and my 68mph minx will run circles around it.
    I will let you know how the Minx...
Results 1 to 25 of 70
Page 1 of 3 1 2 3