There used to be a complete listing of all of the donzis ever made somewhere on this site. I can't seem to find it now. Does anyone know if it still exists and how to get to it?
Type: Posts; User: A2VeeDub; Keyword(s):
There used to be a complete listing of all of the donzis ever made somewhere on this site. I can't seem to find it now. Does anyone know if it still exists and how to get to it?
I haven't checked on this in a while nor have I had time to mess with my boat yet. A bunch of other stuff got in the way, as usual.
I will let you guys know of any progress or results.
Makes sense about the boots. Thanks for the advice. I just replaced them last season.
Thanks for the info. I will need to get out and take some measurements of where I am now. Unfortunately that means putting the battery back in while it is 20 degrees out, since the drive is up right...
Thanks for the clarification on the x measurement. That makes a lot of sense about leveling the prop shaft.
What do you mean by ultimate around 4.5 inches?
Also any other info on different x...
So what was the final x-dimension of the finished project? This is measured from the lowest point of the "Vee" at the transom to the propshaft centerline with the drive fully trimmed down, correct?
...
Thanks for the reply.
I researched some semi-custom covers sold on Overtons, Boat Covers direct and boatcovers.com.
There were tons of close matches for the boat size, but none of them were...
I need to get a new cover for my '72 18'. I found a few on Walmart's website that had great reviews for around $100. One was made by Harbomaster and one by Gulf Stream. I am not looking to spend a...
I work in 21226. I assume this is Crazy Rays junk yard about two blocks from my office. Let me know if I can help. I am probably going to Crazy Rays tomorrow morning to look for a mirror for my S-10....
I dont remember exactly how much he added. I think it was around 3-4 inches.
Good point. I forgot to mention that he is running tips without any flappers at all. I tell him all the time he...
My fathers boat (22C w/ 454 and stainless marine manifolds) had similar issues. He was running a little bit bigger cam though. He ended up adding extensions to the stainless risers to force the...
What year Wrangler? The older 4.0 I6 was pretty powerful. I think they stopped it around 2005 for the V6. I haven't been in one for quite a while, but my buddies old 99 2 door Sahara wasn't slow by...
I currently have a 100 shot on a sbc in a 1972 18 2+3.
I've gotten very similar results as Just say N2O.
I'm running an alpha drive with ~275hp small block.
With a 23" cleaver I go from 4400 rpm...
Grenaded 2 or 3 a year myself until I put bearing buddies on them. They seem to help tremendously.
The injector issue was recalled. They fixed my brothers '01 for free. That thing went through wheel bearings like crazy though. Said his buddy's '03 did too. Other than that it was a great truck...
I think propping for N2O is somewhat easier in a smaller boat. A 16 or 18 won't struggle as much to get on plane with a slightly oversized prop like a 22 or larger will.
I love the nitrous on my...
You have the tinted lexan wind sheild?
My father had a local shop make him a new piece for the passenger side of his '87 22c. He just brought the boat to the guy with what was left of the...
My buddy who is a merc mechanic told me to set them at 21-3/4" pin to pin. Glad to see that confimed by someone else.
Same as everyone else said. Different combinations of tabs and trim will have different effects.
I find that I can pretty much control it with trim alone if chop is not too great. I speed up with...
Get some ice on that beer! The mountains are turning white!
What drive? Ratio? and prop are you running?
What do you think the hp is?
My father just put a 540 in his '87 22'.
Running a 1.5 ratio bravo.
The shop claimed over 600 hp with the aluminum...
I have a half freshwater kit with just the alpha pump feeding it as well. Never had any issues with cooling up to this point. I generally don't run more than 3500-3700 for extended periods of time...
This summer my father and I went in half each on one of the large vacuum tanks that uses compressed air for vacuum. I think it was like $150 at harbor freight. I just used it a few weeks ago for the...
I wonder how much damage those things actually sustain. Aside from some of the really bad ones (rolling across the ground or fully capsizing), it looks like you could just push them right back in and...
I would be very interested in this info as well.