Sounds like a great setup. and with that trailer a good value.
You seem to know witch areas are important already to inspect, but also keep in mind without a survey you get what you see and...
Type: Posts; User: Rumblefish; Keyword(s):
Sounds like a great setup. and with that trailer a good value.
You seem to know witch areas are important already to inspect, but also keep in mind without a survey you get what you see and...
Allstate Here. (California)
$485.00 per year for two boats (Quoted Value ...Donzi 22 @ 30k, Sea Ray 230 @ 15k)
Thanks for that guys!!.... Im off to celebrate and stay up until at least 9:15pm. ( or at least dark )
Well im half off. it was taperd bolt through and the torq spec was 45 lbs ..just torq them and you were done.
Only way to compensate loose lash settings was increasing push rod length.
Hello Don!!. Well its seems everyone right on this one.. the era of GM studs on big blocks toward the late 90's was a taper stud that resembled the old style with the only differnce being a severe...
Agree. I was just Reading this and as I was entertained by some of the post I must say the donzi dudes intent is to be harmfull and attacking.
He should start his own thread and not hi-jack a...
Sorry to hear .. but as you know water doesnt compress very well so time for a leak down...
Also big block chevys usally have .002-.0025 clearance in the bearing depending on who built the...
I know you already know the answer Don.. looks like a tired glazed cylinder. No leak down? ( that would have atleast hissed out the breather)
Going from your description.. I would pull it.
As Said (Mop) you do need to attempt removing carbon build up...
But the cause will remain unless you proceed with your plan on carb replace (or repair ) and finalize the correct tune settings.....
Nicely said.....As long as its confirmed you have no igntion (spark) when the key is cycled off. do these items ( especially the carb)
Yes . doesnt apear to have heated as if ran dry for 5-10 second without water...
I would still add a strainer
That was great!! and anyone with kids may not say it.. but trust me you think it!!
("and no you cant go to the bathroom" line killed me )
Makes me want to watch Pulp Fiction.. Thanks for...
yep..... Those years if a fresh key wont work. it will need a new cylinder.
The Bike would be a tough one...( ive seen them at that e.t for 5k to 15k)
But if you find out what the Chassis cert currently is on the T-bird it could be a player in NHRA or IHRA Top Sportsman....
You may want to re read these posts through one more time..
Price will be long forgotton after the boat you have and wanted.. is at the dock waiting for you..
Call Pier 57..
As I set out for a lunch run I tell the wife.. " its a 40 mile run so im going to take it easy and save fuel"
I plane out at 3000 .. trim er up watch the rpms climb to 3300 and set back the rpm...
Nice Boat.. Nice video!.. Dog seems calm even with the loss of steering..
My thoughts are you may have a little too much stern lift and possible the bottom pad is too light to maintain steering...
Im a big block guy.. but....
A supercharged small block would be able to keep a torque curve to pull a 26p or so in to higher rpms if electronic rev limiting would be changed .
Where as a...
Wax with PTEF
Im not sure the true contents are of Wax with PTEF , but as I noticed the exhaust stains on the white that only hull cleaner could clean, I used this wax in the affected hull...
Yes.. Impeller Check. could be down to 1 fin.. plus as stated above your secondary issue may be cam design versus pulsing of overlap at low idle speed. Check your not idled down to far.. Its possible...
Im looking for the same.. Hoist kept 22 looking fo a soft poly cotton type on top of the cockpit cover. The cover I have now is nylon and i worry about scuffing in the wind.
So what did you find?
Same program here ... If I get one. great. The timing of the post and his issues cancel out my desire for the shirt...the donation is now the same intent with or with out the shirt.
Nice... Even with the sofa chairs.(nice touch)
You may go into detail on the materials used and process.. looks great!!
Agree with you there.. They want to be compliant visually.. but not really increase any brake performance. Maybe too much pressure could be a bad combo on a surge brake with no true way to regulate...
Depending on your surge brake power ( bore size equals brake pressure) you will be taking a step backwards in braking power by adding an axle and brake system.
Not knocking the braking power of...