Search:

Type: Posts; User: FitchPowerboatServices; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    48
    Views
    162,353

    We agree !!

    We agree !!
  2. Replies
    48
    Views
    162,353

    We had some lookers for sure ! Some guys look at...

    We had some lookers for sure ! Some guys look at them and it reminds them of where they started and it usually sparks up a good conversation that usually ends with them saying how much fun they had...
  3. Replies
    48
    Views
    162,353

    Drone pic

    Drone pic
  4. Replies
    48
    Views
    162,353

    We finished it in August and went directly to an...

    We finished it in August and went directly to an event over on the St. John’s River. Unfortunately my brother had to stay home due to Covid quarantining ☹️ But we still had fun. Then in September...
  5. Replies
    48
    Views
    162,353

    I love the look of the boat with the stainless...

    I love the look of the boat with the stainless handrails removed
  6. Replies
    48
    Views
    162,353

    Transom pic

    Transom pic
  7. Replies
    48
    Views
    162,353

    I just realized that I never finished this thread...

    I just realized that I never finished this thread although the boat was finished in August, I apologize for this.

    A quick recap of what was done

    Fuel tank replaced
    Transom replaced...
  8. It was a Rev4 but it was a 23P the 25P is on your...

    It was a Rev4 but it was a 23P the 25P is on your new boat. That little Stroker motor was HOT and it would turn that 23p to 5K easily and put it on the limiter in a little chop. I tried a few...
  9. Replies
    48
    Views
    162,353

    Rigging grommets

    Rigging grommets
  10. Replies
    48
    Views
    162,353

    I think they are made by TH Marine but I’m not...

    I think they are made by TH Marine but I’m not sure. We use them all the time when doing rigging jobs. I keep them in stock so I’ll post a pic of them tomorrow with the part number.
  11. Replies
    48
    Views
    162,353

    Thanks I like the smooth finish a lot. That...

    Thanks I like the smooth finish a lot. That engine compartment originally had carpet on the floors and inside of the hull. It was so nasty I couldn’t wait to get rid of it.
    We moved the battery...
  12. Replies
    48
    Views
    162,353

    Engine in

    Engine in
  13. Replies
    48
    Views
    162,353

    Finally made some progress rigging the boat.

    Finally made some progress rigging the boat.
  14. How about trimming the drive neutral and getting...

    How about trimming the drive neutral and getting a measurement on the propshaft depth. Measure from the bottom of the boat to the centerline of the propshaft. You can use a straight edge next to the...
  15. Replies
    8
    Views
    638

    If the boat wasn’t originally setup for an ITS...

    If the boat wasn’t originally setup for an ITS your going to want to go ahead and order a -2 lower when you order the new ITS assembly. The transom is cut a little on the deep side on a production...
  16. Replies
    48
    Views
    162,353

    I have to apologize Greg, when I told you it was...

    I have to apologize Greg, when I told you it was a 2 stringer boat I was going off what I had seen in the engine compartment. When I cut the deck to remove the tank I found that it has 2 additional...
  17. Replies
    249
    Views
    79,033

    I know where your at. I’ve been trying to get...

    I know where your at. I’ve been trying to get my life project free for the last 12 years and if I don’t buy anything else it looks like I have 2 more years to go. It doesn’t help that my...
  18. Replies
    48
    Views
    162,353

    We had to get over that a long time ago 😎 But...

    We had to get over that a long time ago 😎 But it still takes us forever to install hardware on a blank boat measure 10 times, stand back, look at it from every angle possible then cut/drill
  19. Replies
    48
    Views
    162,353

    One more

    One more
  20. Replies
    48
    Views
    162,353

    Now it was time to clean her up and get her over...

    Now it was time to clean her up and get her over to Chris at Brand’s Marine for some fairing and paint work
  21. Replies
    48
    Views
    162,353

    I hated the carpeted engine room since the day I...

    I hated the carpeted engine room since the day I bought this boat so I sanded the engine room cleaning up all of the edges of the glass. Used a little putty in a few spots to smooth some things out. ...
  22. Replies
    48
    Views
    162,353

    So as I had mentioned in one of my earlier...

    So as I had mentioned in one of my earlier post’s someone had cut the rear skin of the transom off at one point and replaced the transom backwards. I had some really fine cracks on the exterior of...
  23. Replies
    48
    Views
    162,353

    After awhile we just let it do what it was going...

    After awhile we just let it do what it was going to do. I figured out how to stow the normal stuff that was always in the boat with bungee cords but when we went on overnight trips our bags would end...
  24. Replies
    48
    Views
    162,353

    One more

    One more
  25. Replies
    48
    Views
    162,353

    Now I mocked up the tabs, built the engine room...

    Now I mocked up the tabs, built the engine room floors (3/4 Carboncore), removed the stainless handrails and glassed the holes , fixed some stress cracks on the top cap, glasses the floors down and...
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4