I recently posted an album of e-drive schematics and parts lists under my profile. Please let me know if you can't view them.
There are several different versions of e-drive and different gear...
Type: Posts; User: Danny; Keyword(s):
I recently posted an album of e-drive schematics and parts lists under my profile. Please let me know if you can't view them.
There are several different versions of e-drive and different gear...
I went from the 270 to the 280T. Matty and f_inscreen are right on in what they are saying about the 2 outboard hydraulic lines and sealing .
I made my own template off another boat very similar to...
Thanks to those that responded, looks like there is going to be some trial and error when I get to trying props.
The videos are great, a resource that I wish I had 10 years ago.
If you go to my...
I have a 1967 Ski-Sporter with a 302 Ford Interceptor and a Volvo 280TE drive.
I am interested in knowing what people with similar E-Drive setups are using for propellers.
My E-Drive has a...
Just came across a 1996 Donzi 22C at a small dry land marina in Muskoka Ontario. Bit of a fixer upper. Red and white, no windscreen.
May have had some hull repairs, a LOT of checking/ cracking in...
Planning a road trip to Florida so I am going to look for a 1990 F-18 while I am traveling. This link will show you exactly the boat I am looking for...
MOP is correct , the unit he describes are the 270T and some early 280Ts. The elephant ears are the more common AQ280 PT. You can find schematics for both on http://www.marinepartsexpress.com/ for...
I too use the Moeller vacuum pump. I run the motor to warm up the oil and I have no problems get it to come up the dipstik. The top of my dipstick tube has a fitting to screw directly on to it. The...
Let me know what I will owe you. No rush, I don't need them right away. Maybe cross paths sometime in Honey Harbour when you going to the cottage.
Have a good Holiday..
Thanks Danny
Hi Rob
What do you have?
I am taking the deck of my 67-16 this winter and this may be a good item to have in stock for that project. Going to Pat's(Little Gibralter) between Christmas and New...
I looked at it a few weeks ago , not that I need another just out of general interest. When you see a Donzi you simply have to stop and take a closer look. Yes nice restoration, new upholstery,...
My 67 -16 had an Eaton Interceptor. Still have the Interceptor but the Eaton drive was replaced I believe in the early 70's with a Volvo 270. May have been done back at the factory, but I'm not sure....
350 ChrisCraft,FLV (LT1 vette based)same issues with the dipstick.
I agree that the time to check it is when the motor is cold and all the residual oil has drain out of the tube. I tried to figure...
1973 21 GT with a fresh 350GM approx 290 HP. Volvo 280 drive. Last year with the old motor I was using a Michigan aluminum 14x23 and it allowed me to turn 5200rpm. I want to reduce my rpm. I want to...
According to my prop guy mine is a mercury racing prop shaft, the spline count is 15. Came with 12x26 mercury props.
Danny
Mine are 1.41:1, there were 4 or 5 different ratios , the parts catalog pages I have shows, 1.45:1 1.41:1 1.26:1 1.18:1. There may have been more as you said 1.51:1 . There were 4...
Are we talking about e-drives. The whole drive or just the lower unit?
Do you know what ratio the drive is?
Diameter and pitch of the props?
Transom plate, hydraulic trim & tilt or the electric...
A couple of yaers ago there was a great thread from a gentleman that built a wooden deck for his 16 with a single bench seat, like a gentleman's racer. I have search for the link and I can't find it,...
Broke the tool, cut myself, sounds like you had Murphy working with you.
Glad to hear that it came off. I can empathize with the whole scenario.
Danny
33855
I apologize for my poor drawing skills.
I sheared off all of the casing of the filter down to the base. Then I made a wrench / tool to match the holes in base. I use a piece of oak at the...
Lenny
No luck on that lead, they have nothing that new,1973?
So if anyone has any leads on manuals for a ChrisCraft engine Model #350FLVTHP
pleas let me know.
Thanks Dan
Thanks Lenny, I sent them an email last night, I'll keep you posted
Danny
Anyone have a source for old Chris Craft manuals, looking for both service and operator manuals that go with 1973 350 GM block, I think it was the LT1 Corvette engine.
thanks Dan
Someone took (dare I say stole) the oil dipstick out of my GT this winter. 1973 GT with 350 GM LT1 engine that was marinized by Chris Craft, I know that there are a few of these engines in older...
Hi Fred
Can't comment about the balancing.
Was in Larry's shop a couple of weeks ago and saw your boat. I think Rob did a hell of a job on it. I watched it at different stages because I wanted to...