Need help finding Plexie Glass Windshield Pieces!!

[cherry82482]

While towing my boat to the lake, a large rock came off the road and smashed into the front my plexie glass windshield. I own a 16 FT 2001 Classic. The windshield looks exactly like the 16 Classic on the Donzi marine website. Please direct me to the proper vendor for help.:wink:

[LakePlay]

I am pretty new here but any local plastic fabricator should be able to copy the broken piece. Or maybe you can get it from Donzi?

[zelatore]

I can't say for sure that it's a match for the current stuff, but like Lakeplay said, any local platics shop should be able to duplicate it.

I had a similar problem with my 22 a year ago. I just took the broken parts down to a Mr. Plastics franchise and they had a new part for me the next day for about $150 as I remeber.

[Stan]

Donzi Windshield 22 Classic

Windshield Installation Story & Material for Sale

I just re-did the windshield on my 1989 22 Classic and have enough pieces left over to make another windshield.

My Windshield story:

I used 3/8 inch Polycarbonate made by Hyzod AR-2 # 7135. This is the BEST material you can use…PERIOD ! The 3/8 inch Polycarbonate is stronger and less flexible then the original 1/4 inch that was there. I also used the AR-2. That means "Abrasion Resistant" on BOTH sides. 7135 is the degree of darkness.

If any of you have called around for this stuff, you know it's hard to find. The ¼ in AR-1 # 7135 was almost impossible to get without ordering the six sheet minimum ! And when I did find some Polycarbonate in 1/4 in # 7135 ............ it still needed to be Abrasion Resistant coated for an extra charge of $ 125 per side. Trying to get the
3/8…….forget about it !!

I gotta tell you, I got lucky ! I called about 20 places here in Southern calif, and finally found 1 sheet of the 3/8 stuff. I only wanted the AR-1, but when they said they only had a sheet of the AR-2, I said " ITS MINE !!! ".

Drove out about 50 miles on a rainy Saturday morning, old windshields in hand. I was going to cut the pieces myself at home, but after seeing and talking to the guys there, I decided to have them cut the stuff for me, and boy, am I glad I let the pros do it.

They first cut the large sheet into 2 smaller more manageable sheets. They then placed the old windshields on top of the new pieces, securing one to the other using 2-sided tape (very smart) no clamps to get in the way. They then used a shaper (basically an upside down router) and traced the outline of the old pieces…..drilled the holes…..cleaned up the edges with a disc sander……..bingo all done. Took about 45 minutes. I used the old grommets from the previous plastic pieces.

I am confident I could have done as nice a job as the pros, but for a lot more time and thinking ! When you know how to do something right (the first time) it's easy.

Remember……."measure 3 times …cut once !! "

The 3/8 Polycarbonate Hyzod AR-2 4x8 sheet cost me $ 425 with sales tax ( and $ 80 bucks to cut ). From my calling around, this was a very good price, with NO shipping charge. So I'm in about $ 500 bucks. REMEMBER ….this is the 3/8 stuff, NOT the ¼.

For the ¼ stuff, I got quoted $180 a sheet plus $ 125 per side for Abrasion Resistant coating = $ 430 plus tax.and cutting.

I was hoping there would be enough material left over to do another windshield for a 22. But that's not going to happen. BUT, there is definitely enough to do a windshield for an 18 Classic or similar. The windshield on the 18 should be the same length as the 22 but the width is not as much. The side pieces, I figure about 38 inches in length and the width is also less than on a 22.

The 2 pieces I have left are :
71 3/8 x 14 1/8
48 ½ x 17
Polycarbonate Hyzod AR-2 # 7135


I know you can get a new windshield out of the big piece. I had an 18 classic and according to my measurements, I am confident you can get 2 sides from the smaller piece, but please check your own boat before buying this.

$ 225 plus the shipping…$ 25 bucks $ 250 Total

This way I recover some of my cost. If you think its expensive, that’s ok.......try finding this stuff !


Stan

Seh1@aol.com

818-406-1802

[joseph m. hahnl]

http://cgi.ebay.com/ebaymotors/DONZI-22-CLASSIC-WINDSHIELD-Fits-1986-1988-others_W0QQitemZ180285266923QQcmdZViewItem?hash=it em180285266923&_trkparms=39%3A1%7C65%3A1%7C240%3A1318&_trksid=p4506.c0.m245