PDA

View Full Version : Winshield gromets



MOP
02-25-2004, 12:46 PM
Have found a very reasonable source for the windshield gromets. These are the 3/8 ones that fit my 22C windshield and many others.

Check below for price and drop me an E-mail.

Phil

CaptWK
02-25-2004, 06:55 PM
Have found a very reasonable source for the windshield gromets pictured in my avatar. These are the 3/8 ones that fit my 22C windshield and many others.


I need some email me info.

MOP
02-25-2004, 08:02 PM
Diagram below, fits 3/8 hole, only in black UV resistant.

Ok spoke to supplier this AM, my cost has gone up a bit have to jack price slightly. I will sell a minimum order of "50" a little more then it takes to do the job on our boats for $15.00 inc shipping and handling.

Phil

JimG205
02-26-2004, 07:41 PM
Hi Phil- I'll take 50-E-mail me your address and I'll send you a money order-Thanks-Jim :yippie:

CaptWK
02-26-2004, 08:55 PM
Will be posting price tomorrow should be real cheap, I made a size mistake when I first spoke to the factory and missed the return call.

Diagram below, fits 3/8 hole.

Phil
"Tomorrow" or now!

Ok spoke to supplier this AM, my cost 13.4 cents each. I will sell them to any member interested for 25 cents each to cover the heavy duty envelopes, plus postage. Minimum order 50 that is about what it takes for a plexi windshield and real cheap compared to over the counter.

I will not know what the postage will bo till I mail the first batch. So JimG205 and CatpWK will get free poatage being the first to order.
Same here send me address and thanks:yippie:

farmer tx
03-10-2004, 12:43 AM
Phil, I got the grommets in the mail today and they were just what I was looking for. That is the beauty of this site. Ask a question and someone will come up with an answer. Great promp service also. I am going to install them tomorrow and was wondering if they need a dab of 4200 on the screw threads.

Thanks again,
Mark

Lenny
03-10-2004, 12:50 AM
Nice reply Mark, good to see a post of what it "used to be" again..I'll see ya at Cumberland. :D Lenny

CaptWK
03-10-2004, 05:08 PM
Got my gromets also just what I needed. Great deal and quick service. Thanks again MOP:moped:

RickSE
03-11-2004, 11:21 AM
MOP,
Are these the flexible rubber grommets, blue in color and about 3/16 thick?

MOP
03-24-2004, 11:12 AM
A few of the guys have thier gromets, I have and can get more. I can also get most any rubber part you need. Some have minimum order size which may be a pain but it don't hurt to ask.

Phil

MOP
04-16-2004, 02:05 PM
Just bumping it back up top for guys that need the gromets. PM or Email me if you need them, even with shipping they are less than half what you can get them retail.

Phil

BUIZILLA
04-16-2004, 02:37 PM
MOP, I need 40

MOP
04-16-2004, 02:42 PM
Done, counting them out now!

Phil

MOP
07-10-2004, 07:20 AM
Just a bump to bring this back incase one of you needs them, I have some and can get more. You can drop a note to the guys above to see how they liked them.

Phil

sizeplay
07-12-2004, 10:25 AM
I would like to order some but would like clarification on whether these grommets are the finish washers or the black rubber inserts? Need both., Thanks in advance. You can email me at sizeplay@tampabay.rr.com.


Jim

Donzigo
07-12-2004, 08:08 PM
MOP,

I'll take 50. Where do I send the money?

Richard Aaron
4255 48th Ave. South
St. Petersburg, Florida 33711
727-867-7020

............and thank you so much.

MOP
07-13-2004, 08:19 AM
Rich as discussed sending this AM.

Phil

Donzigo
07-18-2004, 08:25 AM
Phil.

Mucho gracias, the check is going ot on Monday morning. Looks like these will work fine.

Richard

MOP
07-22-2004, 11:58 AM
Just a quick note please E-mail or PM me, just in case I forget to check the post. So far everyone is very happy with these new grommets.

zzrhino
07-29-2004, 01:50 PM
would that size fit a z25 ???please post could use a few thanks zzrhino :cool:

MOP
07-29-2004, 03:39 PM
would that size fit a z25 ???please post could use a few thanks zzrhino :cool:

I am not sure, these fit the Classics with the thick frame less windshields. They fit into a 3/8 hole have decent shank length, accept a #12 screw and a counter sunk finish washer rests on it not on the plexi.

Phil

MOP
07-06-2005, 09:01 PM
TTT I ran out of grommets thanks to some happy Donzi owners so I have just gotten a new shipment, my price went up a tad but the same price to you all!

Phil

TOPSY II
07-07-2005, 07:16 PM
If these will fit my '86 Minx, ship me 50. Tell me where/how to send you payment..paypal, credit card, etc.

THANKS!! :D :D my windshield and I both thank you!!!!

TOPSY II

donzi72
07-12-2005, 10:38 PM
Hi' Phil I'll take 50 E-mail me your address to send payment .Thanks for your
help . jesus :

MOP
08-31-2005, 09:46 PM
TTT
Project time is a coming, I have a fresh shipment. Remember PM or email me for quickest results.

Phil

MOP
06-28-2006, 11:55 AM
TTT If you need them I have them!

MOP
08-01-2006, 04:56 PM
A few have contacted me but did not find the link so BUMP!

MOP
08-21-2007, 05:51 PM
It is getting close to winter project time! I have ordered this seasons grommets for you guy that will be working on your toy!

Phil

MOP
05-24-2008, 09:39 PM
BUMP! Got a PM about grommets, for you other late comers I have the correct ones for our boats! Over time the grommets get old and hard/stiff just like me! Once the become hard/stiff they do not allow for any movement and the windshields can crack from the screw holes. I know both of my cracks originated from screw holes from before I got the boat.

Phil

DON N.
06-02-2008, 10:34 PM
Thanks Phil I Recieved The Grommets Promptly.